-Speckhobbies- 3D PRINTING & CFMOTO ACCESSORIES
3D Printing components & Accessories for 2023 to 2025 CFMOTO G2 Trail & Sport (2026 is untested)
Speckhobbies current products
Blinker Wiring Kit (RED)
- Fits 2023 and newer G2 Trails, Sport & Sport 4.
- No cutting or splicing of wires. Will not void your warranty. All plug & play. This is just a wiring completion kit. Some of the wiring is already installed from the factory.
- Kit comes with RED LED lights.
- To complete you will need to purchase a 'Flasher Unit' (part #5BWV-161000-5201) and a 'Turn Switch' (part #5ASV-169060-6001) from your dealer or a reputable parts place. You will also need the 'Inner Hex Bolts, M6x20, Pack of 2' (part #5BWV-040008-5000) and some 'Nut Clips' size M6x1mm to mount the flasher unit to the firewall in front of the Power Steering motor.
- If you require a 'Hazards' option, you'll also need a 'Hazard Switch' (part #5ASV-169070-6001).
- This item has an Under dash 12V Key On/Accessory point built into it.
Blinker Wiring Kit (AMBER)
- Fits 2023 and newer G2 Trails, Sport & Sport 4.
- No cutting or splicing of wires. Will not void your warranty. All plug & play. This is just a wiring completion kit. Some of the wiring is already installed from the factory.
- Kit comes with AMBER LED lights.
- To complete you will need to purchase a 'Flasher Unit' (part #5BWV-161000-5201) and a 'Turn Switch' (part #5ASV-169060-6001) from your dealer or a reputable parts place. You will also need the 'Inner Hex Bolts, M6x20, Pack of 2' (part #5BWV-040008-5000) and some 'Nut Clips' size M6x1mm to mount the flasher unit to the firewall in front of the Power Steering motor.
- If you require a 'Hazards' option, you'll also need a 'Hazard Switch' (part #5ASV-169070-6001).
- This item has an Under dash 12V Key On/Accessory point built into it.
Under dash 12V Key On/Accessory Point
- Fits 2023 and newer G2 Trails, Sport & Sport 4.
- This is a direct plug in 12V Key On/Accessory point for under your dash. No cutting or splicing of wires. Will not void your warranty. This allows you to have a 12V Key On point under the dash instead of running wires through the firewall and under the hood. Uses simple female spade terminal pre-installed for your convenience.
- Simply remove the 4-pin plug cover under the dash in the center and you have a place to attach a 12V Key On power for a relay or whatever you may need.
- This is not a power point. Do not run lights, radios or anything else off of this device. It's simply a way to power on a relay or other powered device by turning on the key.
G2 Radio Pigtail
- Fits 2023 and newer G2 Trails, Sport & Sport 4.
- This Pigtail gives you a waterproof OE plug with 12v Battery, 12v Accessory (key On) & Ground to allow you to hook up your own radio, GPS system or whatever you need these power signals for.
- It could also be used to turn on a relay that provides power to a fuse box for other accessories like rock lights, whips, lightbars, etc...
- Limited to 10 amps
4 Circuit Fuse box
- Fits 2023 and newer G2 Trails & Sports. Does not fit Sport 4.
- If you need one for a Sport 4 email me. It's the same price, I'll just have to add 3 feet of power and ground wire.
- No cutting or splicing of wires. Will not void your warranty. All plug & play.
- This is an IP67 rated fuse box with integrated 30 amp relay that comes on only when the key is on.
- The IP67 rating means that this item can withstand direct water ingress (being sprayed with a pressure washer from 2 or more feet away), it's dust proof and is water proof @ up to 1 meter deep for no more than 30 minutes.
- It has a maximum of 30 amps of usable current and has 4 output leads. Two are fused @ 20 amps (RED 12 awg wires) and two are fused @ 15 amps (BLUE 14 awg wires).
- The fuse box is intended to give you a place under the dash to wire in your switched accessories such as Rock Lights, Light Bars, Radios, Amplifiers or whatever you need 12V key on power for.
G2 Tie Down
- Fits 2023 and newer G2 Trails and Sports.
- Utilize unused bolt points to tie things into the bed of your G2 Sport or Trail.
- Very sturdy. 3D printed from Carbon Fiber reinforce Nylon.
- Testing showed it could hold up to 252 pounds of pull Laterally and up to 220 pounds of pull Vertically.
- Comes with a single tie down and a longer replacement bolt.
- All you need it a Torx T30 bit to remove the stock bolt and an 8mm socket to install the new one.
12 inch Python Bus Cable Extension for Bambu 3D Printers
- Allows you to add a disconnect point outside the Python enclosure so you don't have to fiddle with removing the seal on the rear of the enclosure or disconnecting the cable from the back of the 3D printer.
- This makes it easy to just remove the PTFE tube, unclip the Bus Cable and move the Python enclosure whenever you need to clean it or do maintenance.
- This has come in very handy for me.
6 inch AMS Extension Cable for Bambu 3D Printers
- Used to extend the AMS 6 pin Bus Cable so you don't have to use a special tool to remove it from the back of the Bambu Printer.